All products

N 6656 is a set of brass-plated bi-fold door hinges. They are the non-mortise style used by very many bi-fold door manufacturers. Made of stamped steel, the hinges have a cutout that allows for the non-mortise installed.

N 6705 is a spring loaded, 3/4 in square glide or guide in a 3/8 in plastic base. It mounts on the top edge of a bi-fold door that is 1 to 1-3/8 in THK. Used by Alliance Doors and many bi-fold door manufacturers.

N 6704 is a spring loaded, 3/4 in Dia nylon roller guide in a 3/8 in plastic base. It mounts on the top edge of a bi-fold door that is 1 to 1-3/8 in THK. Used by many bi-fold door manufacturers.

N 6703 is a spring loaded, 7/8 in Dia nylon roller guide in a 3/8 in plastic base. It mounts on the top edge of a bi-fold door that is 1 to 1-3/8 in THK. Commonly used by Kenna Frame as well as countless other bi-fold door manufacturers.

N 6672 is a nylon top-mount bi-fold door pivot. Used by several manufacturers, the spring-loaded 3/8 in nylon pin inserts into the top pivot bracket above creating a pivot point for the bi-fold door.

N 6729 is a guide rod used in Benchmark bi-fold door systems. The 5/16 in Dia, 5-1/4 in L steel rod and is threaded on the bottom half with a hex nut and washer. There is a 3/8 in nylon cap on the end.

N 6702 is a top-mount bi-fold door pivot. Used by several door manufacturers, the 19/32 in spring-loaded pivot pin inserts into the pivot bracket above creating a top pivot point for the bi-fold door.

N 6700 is a spring loaded, 1/4 in Dia steel pivot in a 3/8 in plastic base. It mounts on the top edge of a bi-fold door that is 1 to 1-3/8 in THK.

N 6612 is a spring-loaded 1/4 in steel pivot pin in a steel nail down base. The base is 3/8 in with 2 nail down tabs on either side. It mounts on the top back edge of a bi-fold door.

1/4 in W nylon wheel on spring-loaded steel shaft with plastic housing that tapers to 3/8 in OD to allow for hammering into drilled hole. Self-adjusts from 1-1/2 to 2 in H.

N 6539 is a 4 in L bi-fold door snugger that snaps into the center of the bi-fold door track. The guide pin (N 6545) is inserted between the two springs in the nylon snugger housing. As the door is closed, the snugger slides in the track and makes contact with the opposite set of doors. This applies pressure evenly between guide pins. This causes them to remain in the closed position until one of the sets is grabbed by the knob and pulled outward. Used on Acme bi-fold doors.

N 6823 is a stamped steel top pivot bracket. It fits into the Acme 5/8 in W track. The bracket is inserted into the track and as the screw is tightened, it forces the bracket against the lip running the length of both sides of the track. It is adjustable by moving it back or forth to the best position. It is used with the Acme top pivot N 6672.

N 6707 is a bottom mount pivot used by Johnson Hardware and many other bi-fold door manufacturers. The 7/16 in Dia nylon base houses a 1/4 in pivot bolt with a unique star adjustment nut.

N 6696 is a bottom mount pivot used by many bi-fold doors manufacturers. The 7/16 in Dia nylon base houses a grooved pivot tip that screws in or out for adjustment.

universal design, zinc-plated steel. Mounts to back of lead doors to maintain tight closure in openings not entered from both sides. Includes set of 1-1/8 in H aligners and four #8 x 3/4 in Phillips pan head sheet metal screws.

N 6706 is a bottom mount pivot used by many bi-fold door manufacturers. The 3/8 in Dia nylon base houses a 1/4 in pivot with a hex head nut for adjustment.

Fits on Johnson Hardware doors. Steel bracket with nylon bushing insert to accept pivot pin. 3-1/16 in L x 1 in W overall. Includes two #8 x 1-1/4 in Phillips pan head screws.

N 6673 is a bottom mount pivot used by many bi-fold doors manufacturers. The 3/8 in Dia nylon base houses a grooved pivot tip that screws in or out for adjustment.

Ideal for patching a bicycle tube, air mattress or other rubber inflatables. Fits easily into a pocket or frame bag. Includes patches, buffer and rubber cement.

Use Danco top Bibb gasket washers to fix your leaky faucet. The flat design of these washers helps prevent leaking and provides positive shut-off for your faucet. Repairing a dripping faucet is an easy and inexpensive alternative to replacing the entire fixture. Replacing worn out washers will provide a better seal and prevent leaks.

Designed with a patented one piece 2.4 in Dia mounting flange and inlet connection. Ideal for replacement and new construction installations. Combines a 3/4 in garden hose outlet with a 1/2 in or 3/4 in push to connect inlet. Innovative push to connect design makes for quick and easy installation. Ideal for working in tight spaces. Faster install time and ease of use reduces installation errors.